Dalsa p2 manual

Page 37 These restrictions are all tested w ithin the calibration algorithm and the cam era w ill report an inform al m essage cod e if any of these cond itions cou ld not be m et. Coefficient value in a range from 0 to Page Setting And Reading Prnu Coefficients 0 and for 8-bit d ata Use the m od es, or 0 to for bit d ata m od es.

Page Monitoring The Camera Monitors current line rate Value Function Disable selected task Enable selected task N ote: by d efau lt all m onitoring tasks are enabled except voltage m o nitoring. Page Rebooting The Camera A pre-trigger m ay be requ ired for som e fram e grabbers.

To set the pre-trigger, u se the com m and : sp i Syntax: Syntax Elem ents: Pretrigger value from 0 to If you r system cannot perform flat-field correction after w arm -u p consid er the recom m end ed m ethod s of red u cing d ark cu rrent and overall cam era tem peratu res see below.

Page 44 Both m ethod s— either cond u ction throu gh heat sinking, or convection throu gh air flow — greatly red u ce d ark cu rrent and w ill im prove you r system perform ance. Page 45 Page 46 M3x0. Page Light Sources d esired object resolu tion size. Page Ccd Handling Instructions H ow ever, the friction betw een the ru bber and the w ind ow m ay prod u ce electrostatic charge that m ay d am age the sensor.

Page Cleaning The Sensor Window 5. Wipe the w ind ow carefu lly and slow ly. When cleaning long linear sensors, it m ay be easier to w ip e along the w id th i. Und er specifications. Ad ju st the analog offset u sing the light cond itions, you shou ld receive a valu e. Page Specific Solutions Do not attach w ires to u nu sed pins. Verify that the cam era is not receiving spu riou s inpu ts e. Page Noisy Output Probe the ou tpu t lines w ith an oscilloscope.

Disconnect the d igital cable from the cam era and check the d igital signals at the ou tpu t of the cam era. Page Horizontal Lines Or Patterns In Image If you have verified that you r exposu re tim e is consistent and patterns of low frequ ency intensity variations still occu r, ensu re that you are u sing a DC or high frequ ency light sou rce.

All u nu sed d ata bits m u st be tied to a know n valu e by the cam era. Falcon Material Composition Product Declaration. Falcon2 12M 8M 4M Datasheet. Falcon2 User Manual.

Falcon2 Declaration of Conformity. Falcon2 Material Composition Product Declaration. Falcon2 User 3D Model. Genie C Datasheet. Genie M Datasheet. Genie Color Series User Manual. Genie Mono Series User Manual. Genie Material Composition Product Declaration. Genie TS C Datasheet. Genie TS M Datasheet. Piranha Color Datasheet.

Piranha Color Manual. Piranha ES 12k Datasheet. Piranha ES 4k and 8k Datasheet. Piranha ES 12k User Manual. Piranha ES 4k and 8k Manual. HSLink Technical Primer. Piranha HS 12k Datasheet. Piranha HS 4k Datasheet. Piranha HS 6k Datasheet. Piranha HS 8k Datasheet. Piranha HS 12k User Manual. Piranha HS 4k Manual. Page Camera Link Serial Communication 2. The following chapter describes how to configure the camera using the serial interface.

Retrieving Camera Settings To read current camera settings, send the command. For an explanation of the camera parameter screen, see section C6 Camera Parameter Screen on page Page Command Format For example, the analog gain value can be set to —5db in calibrated mode and 6dB in uncalibrated mode. When switching between calibrated and uncalibrated modes, the camera automatically uses the corresponding value.

Refer to Setting the Exposure Mode on the following page for details. This functionality can be used to verify camera operation and to perform basic testing without having to connect the camera to a frame grabber. This information is also used for collecting line statistics for calibrating the camera. The number of lines to sample is set and adjusted by the command.

The camera displays the Min. If you are using a region of interest, the camera displays the statistics for the region of interest only. Page Optimizing Offset Performance 10 20 3. Page 32 When subtracting a digital value from the digital video signal the output can no longer reach its maximum. Use the ssg command to correct for this.

See section 3. Page Setting Gains Note: This function requires a constant light input while it executes. This feature is beneficial for achieving a common output level for multiple cameras in a system. The fixed offset FPN is determined first by performing a calibration without any light. This calibration determines exactly how much offset to subtract per pixel in order to obtain flat output when the CCD is not exposed.

Page 36 PRNU procedure. Dark Calibration Dark calibration is used to remove the fixed analog offset from the video path. Page 37 2x, the camera will not be able to compensate for extremely non-uniform light.

These restrictions are all tested within the calibration algorithm and the camera will report an informal message code if any of these conditions could not be met. Coefficient value in a range from 0 to Page Setting And Reading Prnu Coefficients "aa", "55", "aa", "line counter", "line average", "pixels above threshold", "pixels below threshold", "derivative line sum". To activate the end-of-line sequence, use the command. Page Rebooting The Camera Previously saved pixel coefficients are also restored.

To set the pre-trigger, use the command: Syntax: sp i Syntax Elements: Pretrigger value from 0 to Note: Upon initial power-up the front plate camera temperature is near ambient.

Home Support Documentation Manuals. Genie Nano User Manual. Rad-icon User Manual. Shad-o-Scan User Manual. Astrocyte User Manual.